It always surprises me how few people have heard of a spray bar.
While they certainly aren’t for everyone, there is no denying that a spray bar can be a very useful piece of aquarium equipment.
In fact, they are so useful that many people go the DIY route and create their own custom spray bar just for their aquarium.
But what is a spray bar? And do you need one in your tank?
Let’s find out!
- What is a spray bar?
- Why do you need a spray bar?
- Where do you place your spray bar?
- How do you increase or decrease the spray bar pressure?
- What is the best spray bar kit?
What is an aquarium spray bar?
You know those sprinkler tubes that attach to the end of your garden hose?
Yeah, that one!
Well, a spray bar is similar to that, except it sits on the filter outlet or water pump – gently spraying filtered water back into your tank.
Some brands of internal filters even come with a built-in spray bar.
What does a spray bar do?
As you likely already know, oxygen enters the water of your aquarium through the surface.
Well, a great way to increase the amount of oxygen in your tank is by agitating the surface water of your aquarium.
That’s where a spray bar comes in.
A spray bar is one of the many aquarium products available, such as air stones, that can be used to agitate the surface of your aquarium.
The spray bar attaches to your filter outlet and evenly sprays the water across the surface of your aquarium.
Spray bars are typically installed in the horizontal position. After all, it’s spray bar, not spray pole.
As the spray hits the water, it churns the surface, allowing more oxygen to enter the water.
Spray bars also benefit your tank by creating water movement, an essential part of a healthy tank. Besides betta and gourami, there are not a whole lot of fish that will happily live in stagnant water!
Whether you need a spray bar or not will entirely depend on your current set-up.
If your aquarium has good surface agitation and movement already, then a spray bar doesn’t have a whole lot to offer.
But if you have dead spots in your tank or are looking for some gentle water movement, a spray bar is just the tool you need.
You can also use a spray bar to decrease surface agitation. By aiming the spray bar at the glass, the water will gently trickle down into your tank.
Where do you place your spray bar?
The ideal location for your spray bar will entirely depend on your tank.
Consider the following points when deciding on the right spot.
1. On the rear of your tank or on the side?
If you are using a spray bar to create water flow, I would recommend placing it on the rear of your tank.
Unless you have an unusual shaped tank, the distance from the front to the rear will be shorter than one side to the other.
The shorter distance makes it easier to create constant circular water movement throughout your tank, like this…
If you place the spray bar on the side of your tank, the water current has to move further, which can result in incomplete water movement…
On the flipside, if you have your filter inlet on one side of the aquarium and you place your spray bar on the other, you can get a nice current flowing across your tank.
1. Above the water or below it?
While the majority of hobbyists position the spray bar above the water, it may surprise you to learn that you can also place it underwater.
The main benefit of this is you can create gentle and even water movement throughout your aquarium without rough surface agitation – perfect for planted tank owners who are injecting CO2 into their aquariums and want to create as little surface agitation as possible.
Another advantage of placing the spray bar under water is that you won’t hear any splashing sounds as the spray hits the surface of your tank – although I actually find the soft pattering sound relaxing, it sounds like rain to me.
But to get the best surface agitation, you will want to use a spray bar above the water.
3. Angle the spray bar up, across or down?
If that wasn’t enough choice for you, now you need to decide exactly what direction you are going to point the holes of the spray bar in.
This will decide where and how the stream of spray hits your aquarium.
Let’s take a closer look at the effect angling a pray bar can have on performance.
Above Water Spray Bar Placement
1. Angled towards the front of the tank
In order to create even water movement across the surface of your aquarium, position the spray bar so that the holes are pointing horizontally across the surface of the water.
2. Angled downwards towards the rear of the tank
If you just want to create strong surface agitation along a narrow section of your aquarium, you can angle the spray bar downwards, so that it just churns the surface water.
3. Angled towards the glass
Trying to avoid the surface agitation all together? Why not aim the spray bar towards the glass of your aquarium. The spray will bounce off the glass and weaken before hitting the surface of the aquarium, resulting in minimal surface movement.
Underwater Spray Bar Placement
1. Angled Upwards
What is an aquarium spray bar?
You can use the spray bar to gently stir the surface of your water: simply angle the spray bar upwards so that the holes point towards the surface. Spraying the surface from underneath will cause lighter surface movement than spraying it from above.
The further down you place the spray bar, the less the spray bar will agitate the surface.
2. Angled Downwards
Angling the holes downwards, when underwater, will produce a water current in that direction.
If you have a loose substrate, such as sand, you risk the stream from the spray bar blowing it around your tank.
How to increase or decrease the pressure on your spray bar
Did you know that you can increase or decrease the strength of the water stream that shoots out your spray bar?
The pressure of your spray bar will be determined by both the number and size of the holes that run along the length of the spray bar.
The smaller the size of the holes in the spray bar, the stronger the stream.
The larger the size of the holes in the spray bar, the weaker the stream.
The smaller the number of holes in the spray bar, the stronger the stream.
The greater the number of holes in the spray bar, the weaker the stream.
Those of you who are creating a DIY spray bar will have the most control over the number of holes and sizing…
That said, if you have a store-bought spray bar kit, you can increase the pressure by siliconing some of the holes closed or carefully drilling the holes out to decrease flow.
The best spray bar kit – Eheim
You got to hand it to the Germans, they sure know how to make a quality product. Coincidentally, Eheim also makes my favorite auto fish feeder and submersible heaters.
When choosing the correct sized model, the smaller number refers to the internal diameter, which you can use to determine if the spray bar will fit your filter outlet hose/tube.
But what if the sizing doesn’t match your set-up?
multi hose adapter to size the hose up or down to in order to get a proper fit.
You can pick up an Eheim spray bar in two different sizes:
1. Size: 12/16 mm (1/2 x 5/8 inch)
2. Size: 16/22 mm (5/8 x 7/8 inch)
So, what I like most about the Eheim spray bar kit is that you can piece it together any way that you see fit.
Whether you want a long continuous run or you want to bend it at 90 degrees around the corner of the tank, the option is yours – the sturdy suction cups will hold it any way you see fit.
At the time of writing this, no other commercially available spray bar kit comes close!
When used correctly, spray bars can be a very effective at agitating surface water and producing water flow in your aquarium.
Oh and don’t forget…spray bars, like everything else in your tank, will require maintenance every now and again. I personally use a flexible cleaning brush to remove gunk from the narrow tube – it works great!
So be sure to periodically clean out your spray bar to prevent debris and gunk from impacting its performance.
It is also worth mentioning that spray bars are very obvious. I mean, they are essentially a big hunk of plastic in your tank. While spray bar kits are more subtle than DIY spray bars, they still stand out in your aquarium.
If you want a product that sits on the outlet of your filter, can agitate the surface water, and is nearly invisible – then you should check out a lily pipe!
Do you use a spray bar in your aquarium? Let me know in the comments below!